莊可佳，男，出生於1988年1月，博士，武漢理工大學機電工程學院副教授。
基本介紹
- 中文名：莊可佳
- 出生日期：1988年1月
- 職業：教師
- 畢業院校：華中科技大學
- 學位/學歷：博士
人物經歷,研究方向,學術成果,科研項目,發表論文,
人物經歷
2006.09～2010.06 華中科技大學機電科學與工程學院本科
2010.09～2016.03 華中科技大學機電科學與工程學院碩博連讀
2016.04～至今 武漢理工大學機電工程學院
研究方向
數控加工過程物理仿真及其表面完整性
數據驅動的製造可靠性及工藝調控
學術成果
科研項目
1. 國家自然科學基金（青年基金） 基於雷射加熱輔助的高溫合金高效銑削界面熱影響規律及實驗研究 2018-2020 負責人
2. 軍工項目 製造過程可靠性分析 2019-2020
3. 湖北省青年基金 壓氣機葉片機器人磨拋機理與關鍵技術研究 2017-2018 負責人
4. 數字製造裝備與技術國家重點實驗室開放基金 難加工複雜葉片預熱輔助切削加工工藝及機理研究 2017.03-2019.03 負責人
5. 武漢理工大學自主創新基金等
發表論文
1. Zhuang KJ, Zhu DH, Zhang XM*, Ding H (2014) Notch wear prediction model in turning of Inconel 718 with ceramic tools considering the influence of work hardened layer. Wear 313 (1):63-74 (SCI, Q1)
2. Zhuang KJ, Zhang XM*, Zhang D, Ding H (2013) On cutting parameters selection for plunge milling of heat-resistant-super-alloys based on precise cutting geometry. Journal of Materials Processing Technology 213 (8):1378-1386 (SCI, Q1)
3. Zhuang KJ, Weng J, Zhu DH*, Ding H (2018) Analytical modeling and experimental validation of cutting forces considering edge effects and size effects with round chamfered ceramic tools. ASME-Journal of Manufacturing Science and Engineering 140 (8):081012-081012-081016. doi:10.1115/1.4040087 (SCI, Q1)
4. Zhuang KJ, Zhu DH*, Ding H, (2018) An analytical cutting force model for plunge milling of Ti6Al4V considering cutter runout. The International Journal of Advanced Manufacturing Technology 94 (9-12):3841-3852. doi:10.1007/s00170-017-1078-3 (SCI, Q2)
5. Zhuang KJ, Zhang XM*, Zhu DH, Ding H (2015) Employing preheating-and cooling-assisted technologies in machining of Inconel 718 with ceramic cutting tools: towards reducing tool wear and improving surface integrity. The International Journal of Advanced Manufacturing Technology 80 (9-12):1815-1822 (SCI, Q2)
6. Weng J, Zhuang KJ*, Hu C, Zhu D, Guo SS, Ding H (2018). A novel approach to thermal modeling based on three-dimensional analysis in turning Inconel 718 with round insert. Journal of Materials Processing Technology 266:588-598.
7. Weng J, Zhuang KJ*, Zhu DH, Guo SS, Ding H (2018) An analytical model for the prediction of force distribution of round insert considering edge effect and size effect. International Journal of Mechanical Sciences 138-139:86-98. doi:https://doi.org/10.1016/ j.ijmecsci.2018.01.024 (SCI, Q1)
8. Zhu DH, Xu XH, Yang Z, Zhuang KJ*, Yan SJ, Ding H (2018) Analysis and assessment of robotic belt grinding mechanisms by force modeling and force control experiments. Tribology International 120:93-98. doi:https://doi.org/10.1016/j.triboint.2017.12.043 (SCI, Q1)
9. Weng J, Zhuang KJ*, Chen D, Guo SS, Ding H (2017) An analytical force prediction model for turning operation by round insert considering edge effect. International Journal of Mechanical Sciences 128:168-180 (SCI, Q1)
