短流保護(Short current protection,簡稱SCP),一種電學名詞。
基本介紹
- 中文名:短流保護
- 外文名:Short current protection
- 別名:SCP
- 所屬學科:電學
短流保護(Short current protection,簡稱SCP),一種電學名詞。
短流保護(Short current protection,簡稱SCP),一種電學名詞。 ...
短路保護的方法 實施短路保護最簡單的一種辦 法是裝設熔斷器,其次是利用電流突然增大和電壓突 然下降的電流電壓繼電保護,具體的可分為有時限(定 時限或反時限)的過電流保護、無時限或有時限的過流 速斷保護、三段式過流保護電流電壓連鎖有時限過流 或速斷保護等。中國煤礦井下最常用的是由電磁式繼 電器組成...
鑒於電源電路存在一些不穩定因素,而設計用來防止此類不穩定因素影響電路效果的迴路稱作保護電路。比如有過流保護、過壓保護、過熱保護、空載保護、短路保護等。簡介 在供電系統中,最容易發生的故障是短路,過載,接地和雷擊等。為了保證供電系統能夠安全可靠地運行,必須安裝保護裝置,以便監視供電系統的工作情況,及時發現...
電流保護classical control theory,電力術語,當線路發生短路時,重要特徵之一是線路中的電流急劇增大,當電流流過某一預定值時,反應於電流升高而動作的保護裝置叫過電流保護。簡介 當線路發生短路時,重要特徵之一是線路中的電流急劇增大,這就需要設定相應的當電流流過某一預定值時,反應於電流升高而動作的保護裝置叫...
為此,通過新增電流差動保護(該保護引入這兩個斷路器的CT信號作為差動信號),來識別並切除這一段聯線上的故障,該保護即短引線保護。基本概念 是一種繼電保護類型。是指3/2斷路器接線或橋型接線或擴大單元接線中,當兩個斷路器之間所接線路或變壓器停用時,由於該線路或變壓器的主保護退出,兩個斷路器之間的一...
過流保護 過流的原因 當電力電子變換器內部某一器件擊穿或短路,觸發電路或控制電路發生故障,出現過載,直流側短路,可逆傳動系統產生環流或逆變失敗,以及交流電源電壓過高或過低,缺相等,均可引起變換器內元件的電流超過正常 工作電流,即出現過流。由於電力電子器件的電流過載能力比一般電氣設備差得多,因此必須對...
當出現負載短路、過載或者控制電路失效等意外情況時,會引起流過穩壓器中開關三極體的電流過大,使管子功耗增大,發熱,若沒有過流保護裝置,大功率開關三極體就有可能損壞。故而在開關穩壓器中過電流保護是常用的。最經濟簡便的方法是用保險絲。由於電晶體的熱容量小,普通保險絲一般不能起到保護作用,常用的是快速...
反時限是指保護裝置的動作時間與短路電流的大小成反比。當流過繼電器的電流越大時,其動作時間就越短;反之動作時間就長。這種動作時限方式稱為反時限,具有這一特性的繼電器稱為反時限過流繼電器。反時限過流保護 同一線路不同地點短路時,由於短路電流不同,保護具有不同的動作時限,線上路靠近電源端短路電流越大,...
《直播與短視頻行業未成年人網路保護白皮書(2023)》,於2023年5月11日,在“2023中國網路表演(直播與短視頻)行業年會”上正式發布。發布信息 2023年5月11日,以“新時代 新直播 新舞台”為主題的“2023中國網路表演(直播與短視頻)行業年會”在北京舉行。《直播與短視頻行業未成年人網路保護白皮書(2023)》在...
短流 短流又稱“短嘴”。管狀流的式樣之一,流行於唐代。歷史淵源 唐代越窯注子、長沙窯注壺有此流式,有白瓷和青瓷製品。
在工程實際中,廣泛採用電流速斷保護和限時電流速斷保護作為主保護,利用定時限過電流保護作為後備保護,當保護裝置處於電網終端附近 時,其過電流保護的動作時限並不長,在此情況下它可以作為主保護兼後 備保護。處理辦法 在高壓柜上發生的事故:帶時限過流保護(斷路器跳閘並發出信號)作為變壓器的後備保護,當變壓器...
過流保護裝置的短路電流與動作時間之間的關係曲線稱為保護裝置的延時特性。延時特性又分為定時限延時特性和反時限延時特性。定義 定時限延時的動作時間是固定的,與短路電流的大小無關。反時限延時動作時間與短路電流的大小有關,短路電流大,動作時間短,短路電流小,動作時間長。短路電流與動作時限成一定曲線關係。
由於經濟、技術等方面的優勢,直流換流器已得到了廣泛的套用,並且還將進一步發展。Boost升壓電路自身沒有限流能力。Buck降壓電路輸出側有電感存在,因此具備一定的限流能力。本文提出一種具有輸出短路保護能力的DC-DC換流器控制方法,將Boost-Buck背靠背結構的換流器通過合理的控制,使其具有很好的負載短路特性。通過電壓電流...
主保護(main protection)是指當保護區域內發生故障時,預定其領先發生作用的保護裝置。對線路保護來說,當根據系統穩定的要求必須全線短時限地切除故障時,應選用縱聯保護裝置作主保護。當系統穩定允許遠故障點的線路—側以帶時限的保護裝置切除故障時。也可以用帶時限階段特性的距離和零序電流保護裝置中的第Ⅰ段和第...
1)保護的原理最簡單、直接,能比較真實地反映設備溫度,在一定程度上可以反映短路故障。2)根據熱累積的原理動作的保護。3)根據電流的大小來動作的保護。過負荷的危害 電氣線路短時間少量的過負荷通常是允許的,因其負載電流是周期性變化的,它並不對線路造成損害。如電動機啟動電流較大,可高達約7In,啟動時間...
相敏過流保護是利用供電系統中過電流的幅值及其相位角兩個特徵量構成的繼電保護。常用於區分短路電流與大容量電動機的起動電流,以提高靈敏度和可靠性的繼電保護。特點 煤礦井下供電系統的主要特點 是:供電變壓器的容量較小、供電範圍大、 線路長、電纜截面較小,因而常常出現供電 系統遠端兩相短路電流值與同一供電...
電動機的損壞主要是繞組過熱或絕緣性能降低引起的,而繞組的過熱往往是流經繞組的電流過大引起的。對電動機的保護主要有電流、溫度檢測兩大類型。電流檢測型保護裝置 (1)熱繼電器利用負載電流流過經校準的電阻元件,使雙金屬熱元件加熱後產生彎曲,從而使繼電器的觸點在電動機繞組燒壞以前動作。其動作特性與電動機繞組...
零序電流保護:中性點直接接地系統發生接地短路,將產生很大的零序電流,利用零序電流分量構成保護,可以作為一種主要的接地短路保護。零序過流保護不反應三相和兩相短路,在正常運行和系統發生振盪時也沒有零序分量產生,所以它有較好的靈敏度。但零序過流保護受電力系統運行方式變換影響較大,靈敏度因此降低,特別是短...
OCP(over current protection)過電流保護 過電流保護OCP(英文名稱:over current protection)預定當被測電流增大超過允許值時執行相應保護動作(如使斷路器跳閘)的一種措施保護。原理簡介 電網中發生相間短路故障或者非正常負載增加,絕緣等級下降等情況下,電流會突然增大,電壓突然下降,過流保護就是按線路選擇性的要求,...
⑴選擇電氣設備和載流導體,必須用短路電流校驗其熱穩定性和動穩定性。⑵選擇和整定繼電保護裝置,使之能正確的切除短路故障。⑶確定合理的主接線方案、運行方式及限流措施。⑷保護電力系統的電氣設備在最嚴重的短路狀態下不損壞,儘量減少因短路故障產生的危害。計算條件 1.假設系統有無限大的容量。用戶處短路後,...
1 短路在保護接零系統(TN系統)中的套用 在圖3中,設備外殼通過保護線與線路中N線作電氣上的可靠連線,當設備的外殼與帶電體相碰(漏電)時,保護線起到製造短路的作用。電流將從設備外殼經由零線流回中性點。由於零線電阻很小,所以這一短路電流很大,而經由人體到中性點的這條通路電阻很大,電流幾乎為零。由此...
5)斷路器與熔斷器配合使用時應考慮上下級的配合,應將斷路器的安秒特性曲線與熔斷器安秒特性曲線比較,以使在發生短路電流的情況下,具有保護選擇性。6)斷路器作配電線路的保護時,宜選用帶長延時動作過流脫扣器的斷路器,當線路末端發生單相接地短路時,短路電流不小於斷路器瞬時或短延時過流脫扣器整定電流的1.5...
另一種是未端線路短路:因為線路長,有一定的阻抗,短路電流較大(約為額定電流的3-5倍),稱為過流,雖然電流較大,但在0.2-2秒內不至於把線路設備燒壞,所以此情設過流保護,將時限設定在2秒之內,超過此時限就會跳閘保線路和設備,同也可以區分假故障,如大風、雷電造成的短路等。電流速斷就是電流達到這個...
◇按保護對象分為電動機保護(M、P、F)配電保護(L)◇按操作頻率分為頻繁操作和不頻繁操作 ◆模組和附屬檔案的種類與用途 ◇ 主體:具有短路保護 (類似MCCB及熔斷器的短路保護功能) 、自動控制(類似接觸器的遠程控制功能)、就地操作與指示功能。◇ 熱磁脫扣器:具有過載、過流保護等功能,整定電流值包括過載反時限、...
限流器屬於電器元件領域,是一種特別用於限制電流的裝置,其特徵在於它有一個標準環型鐵芯,在所述的鐵芯上纏繞有多芯的銅芯膠包線,在所述的多芯的銅芯膠包線上間隔一定距離分別設定有一個動力電源的接口,一個普通家用電器電源的接口和一個照明電源接口。概念描述 一種用於程控配線架的過流保護元件。在系統擴建...
(2)線路應保護的漏電電流應小於或等於斷路器的規定漏電保護電流;(3)斷路器的極限通斷能力應大於或等於電路最大短路電流; (4)過載脫扣器的額定電流大於或等於線路的最大負載電流; (5)有較短的分斷反應時間,能夠起到保護線路和設備的作用。 2、四極斷路器的選用 是否選用四極斷路器可...
單相短路電流 單相短路電流、in lc-phase shnrt-circuit currant一相導體與保護導體發生短路時流經相一零迴路的電流:單相短路電流是評價和設計保護接零系統設計的基本要素。保護接零系統的單相短路電流不應小於低壓斷路器瞬時動作或短延時動作過電流脫扣器的整定電流的1.5倍;不應小於低壓熔斷器熔體額定電流的4倍。
直流快速斷路器 直流快速斷路器,分斷時間短得足以使短路電流達到其最大值前分斷的直流斷路器。一般是利用強大的短路電動斥力直接把觸頭推開,使機構動作時間只有2~3毫秒,加上一個良好的滅弧室,因此具有很好的限流性能。廣泛用於保護矽整流裝置等大功率的直流用電設備中。